So I have this nice old PAL Sony Trinitron 29X1D that I use for my GameCube normally. Worked always great with that and still does, 60Hz RGB signal, no problem.
When I'm trying to connect my MiSTer to that TV though, I get 70% snow - and not the intentional one from the menu screen. Everything is washed out and the menus are barely visible. Doesn't help to load up a core either, it doesn't really work in a way that is usable.
I know that I have to adjust the .ini in a way to make this happen. I've read a bit about the vga_scaler options but most stuff that I find is for Computer CRTs and nothing I have tried worked for me yet.
I have added my .ini - any help would be appreciated.
- pxl_20230406_11592258qpisq.jpg (1.78 MiB) Viewed 1546 times
Code: Select all
[MiSTer]
key_menu_as_rgui=0 ; set to 1 to make the MENU key map to RGUI in Minimig (e.g. for Right Amiga)
forced_scandoubler=0 ; set to 1 to run scandoubler on VGA output always (depends on core).
ypbpr=0 ; set to 1 for YPbPr on VGA output.
composite_sync=1 ; set to 1 for composite sync on HSync signal of VGA output.
vga_scaler=0 ; set to 1 to connect VGA to scaler output.
hdmi_audio_96k=0 ; set to 1 for 96khz/16bit HDMI audio (48khz/16bit otherwise)
keyrah_mode=0x18d80002 ; VIDPID of keyrah for special code translation (0x23418037 for Arduino Micro)
vscale_mode=0 ; 0 - scale to fit the screen height.
; 1 - use integer scale only.
; 2 - use 0.5 steps of scale.
; 3 - use 0.25 steps of scale.
vscale_border=0 ; set vertical border for TVs cutting the upper/bottom parts of screen (1-99)
bootscreen=0 ; uncomment to disable boot screen of some cores like Minimig.
;mouse_throttle=10 ; 1-100 mouse speed divider. Useful for very sensitive mice
rbf_hide_datecode=0 ; 1 - hides datecodes from rbf file names. Press F2 for quick temporary toggle
menu_pal=0 ; 1 - PAL mode for menu core
hdmi_limited=0 ; 1 - use limited (16..235) color range over HDMI
fb_size=0 ; 0 - automatic, 1 - full size, 2 - 1/2 of resolution, 4 - 1/4 of resolution.
fb_terminal=1 ; 1 - enabled (default), 0 - disabled
osd_timeout=30 ; 5-3600 timeout (in seconds) for OSD to disappear in Menu core. 30 seconds if not set.
; Background picture will get darker after double timout
; lastcore - Autoboot the last loaded core (corename autosaved in CONFIG/lastcore.dat) first found on the SD/USB
; lastexactcore - Autoboot the last loaded exact core (corename_yyyymmdd.rbf autosaved in CONFIG/lastcore.dat) first found on the SD/USB
; corename - Autoboot first corename_*.rbf found on the SD/USB
; corename_yyyymmdd.rbf - Autoboot first corename_yyyymmdd.rbf found on the SD/USB
;bootcore=lastcore ; uncomment to autoboot a core, as the last loaded core.
bootcore=lastcore*.rbf ; boots c64 after system start
;bootcore_timeout=10 ; 10-30 timeout before autoboot, comment for autoboot without timeout.
; Option to load the custom font. Format is plain bitmap 8x8.
; Supported sizes of font:
; 768 bytes - chars 32-127 (only alpha + numeric)
; 1024 bytes - chars 0-127
; 1136 bytes - chars 0-141
; up to 2048 - only chars 0-141 will be used.
; if first 32 chars are empty (for sizes 1024 bytes and more) then they are skipped.
font=font/myfont.pf
; USER button emulation by keybaord. Usually it's reset button.
; 0 - lctrl+lalt+ralt (lctrl+lgui+rgui on keyrah)
; 1 - lctrl+lgui+rgui
; 2 - lctrl+lalt+del
; 3 - same as 0 (lctrl+lalt+ralt on keyrah)
reset_combo=0
dvi_mode=0 ; set to 1 for DVI mode. Audio won't be transmitted through HDMI in DVI mode.
; 0 - 1280x720@60
; 1 - 1024x768@60
; 2 - 720x480@60
; 3 - 720x576@50
; 4 - 1280x1024@60
; 5 - 800x600@60
; 6 - 640x480@60
; 7 - 1280x720@50
; 8 - 1920x1080@60
; 9 - 1920x1080@50
;10 - 1366x768@60
;11 - 1024x600@60
;
; custom mode: hact,hfp,hs,hbp,vact,vfp,vs,vbp,Fpix_in_KHz
; video_mode=1280,110,40,220,720,5,5,20,74250
video_mode=0
; set to 1-10 (seconds) to display video info on startup/change
video_info=10
; Set to 1 for automatic HDMI VSync rate adjust to match original VSync.
; Set to 2 for low latency mode (single buffer).
; This option makes video butter smooth like on original emulated system.
; Adjusting is done by changing pixel clock. Not every display supports variable pixel clock.
; For proper adjusting and to reduce possible out of range pixel clock, use 60Hz HDMI video
; modes as a base even for 50Hz systems.
vsync_adjust=0
; These parameters have the same format as video_mode.
; You need to supply both PAL and NTSC modes if you want vsync_adjust to switch between
; predefined modes as a base. This will reduce the range of pixel clock.
;video_mode_ntsc=0
;video_mode_pal=7
logo=0 ; 0 - disable MiSTer logo in Menu core 