HDMI Output Not Working

[Krathoon]

I flashed an SD card with Mr. Fusion and booted it up in the extra MiSTer I built.
It looks like the HDMI out does not work. I get a black screen. I just use a cable connected directly to the monitor. This cable works totally fine with my other MiSTer.

I let it set a while so that it installed the software. I tried setting the video mode and dvi mode in the mister.ini and I still get a black screen.

So, any ideas?

I could try taking off the IO board.

[GreyAreaUK]

If I'm reading this right, you have two MiSTer systems? If so, what happens if you boot the new one using the SD card from the existing (working) one?

[Beeble]

I killed a HDMI out on one of my DE-10 Nano, was preparing / building a second and plugging stuff in and out.
As far as I know the DE-10 Nano doesn´t like pluggin in / out cables on the HDMI while the system and / or the TV / Monitor is running.

[Krathoon]

If I'm reading this right, you have two MiSTer systems? If so, what happens if you boot the new one using the SD card from the existing (working) one?

Yeah. What I can do is make an image of my working SD card and flash it over to the other one.
I suspect something is going on with the Mr. Fusion installer.

[GreyAreaUK]

If I'm reading this right, you have two MiSTer systems? If so, what happens if you boot the new one using the SD card from the existing (working) one?

Yeah. What I can do is make an image of my working SD card and flash it over to the other one.
I suspect something is going on with the Mr. Fusion installer.

I’d be inclined to just pop it out of the working one, pop it into the Mystery MiSTer, and see what happens. That way you know you’re dealing with a ‘good’ card with no duplication errors.

Unless you’re concerned the good card may get damaged in the Mystery MiSTer, in which case boot the Good MiSTer using the copied card first, just to be sure it copied properly. You probably know all this already…

[Krathoon]

If I'm reading this right, you have two MiSTer systems? If so, what happens if you boot the new one using the SD card from the existing (working) one?

Yeah. What I can do is make an image of my working SD card and flash it over to the other one.
I suspect something is going on with the Mr. Fusion installer.

I’d be inclined to just pop it out of the working one, pop it into the Mystery MiSTer, and see what happens. That way you know you’re dealing with a ‘good’ card with no duplication errors.

Unless you’re concerned the good card may get damaged in the Mystery MiSTer, in which case boot the Good MiSTer using the copied card first, just to be sure it copied properly. You probably know all this already…

Yeah. I will work with the copied card. I am waiting on generating an image of my good card right now.

I would have had it today, but my computer had to reboot over night due to Windows Update. I have now postponed Windows Update for a month.

[Krathoon]

Well, the image I made off the working card is too big for the new card.

So, I put the working SD card into the Mister that is not working.

There is still no HDMI output. So, it is a hardware issue.

I will try running it without the IO board. That might be messing it up.

[MiSTer Consoles]

Well, the image I made off the working card is too big for the new card.

So, I put the working SD card into the Mister that is not working.

There is still no HDMI output. So, it is a hardware issue.

I will try running it without the IO board. That might be messing it up.

Are you connecting the new MiSTer to the same display that the other MiSTer was connected to? If you’re using a different display the video settings on that old SD card may not be compatible. Also are the LEDs blinking on the IO board when you have the old MiSTer’s card in there? That would at least be a sign that the FPGA can read the card.

[Krathoon]

Well, the image I made off the working card is too big for the new card.

So, I put the working SD card into the Mister that is not working.

There is still no HDMI output. So, it is a hardware issue.

I will try running it without the IO board. That might be messing it up.

Are you connecting the new MiSTer to the same display that the other MiSTer was connected to? If you’re using a different display the video settings on that old SD card may not be compatible. Also are the LEDs blinking on the IO board when you have the old MiSTer’s card in there? That would at least be a sign that the FPGA can read the card.

Yes. I am using the same display. The lights were blinking.
I have not tried taking the IO board off and running it without it yet.
That is next.

[antibolo]

I have also recently found that the HDMI port on my DE-10 nano is dead. Can't get a picture no matter what. To make sure this isn't a misconfiguration mishap I tried a to a fresh reinstall to a new SD card and I didn't even see the info screen during the Mr Fusion process. And of course still nothing after the fresh install. Also tried my DE-10 nano "raw" without any addons and still nothing.

I bought my DE-10 nano in 2019 and looking at the current prices has almost made me throw up...

I mostly use my MiSTer over analog out to a PVM so it's not a total dealbreaker, but losing the possibility of using any non-15kHz cores is a huge bummer, so I am still debating whether to fork $$$ buy a new DE-10 nano or not.

[antibolo]

I killed a HDMI out on one of my DE-10 Nano, was preparing / building a second and plugging stuff in and out.
As far as I know the DE-10 Nano doesn´t like pluggin in / out cables on the HDMI while the system and / or the TV / Monitor is running.

There should probably be a warning about that in the MiSTer user docs!

I know there are warnings about the USB-OTG port being easy to break. Looks like hotplugging/unplugging the HDMI port is another thing to be careful about...

[FPGA64]

I killed a HDMI out on one of my DE-10 Nano, was preparing / building a second and plugging stuff in and out.
As far as I know the DE-10 Nano doesn´t like pluggin in / out cables on the HDMI while the system and / or the TV / Monitor is running.

There should probably be a warning about that in the MiSTer user docs!

I know there are warnings about the USB-OTG port being easy to break. Looks like hotplugging/unplugging the HDMI port is another thing to be careful about...

Its not just a DE10. Its always bad to swap a HDMI cable to any device when its on.

[antibolo]

I killed a HDMI out on one of my DE-10 Nano, was preparing / building a second and plugging stuff in and out.
As far as I know the DE-10 Nano doesn´t like pluggin in / out cables on the HDMI while the system and / or the TV / Monitor is running.

There should probably be a warning about that in the MiSTer user docs!

I know there are warnings about the USB-OTG port being easy to break. Looks like hotplugging/unplugging the HDMI port is another thing to be careful about...

Its not just a DE10. Its always bad to swap a HDMI cable to any device when its on.

Good to know. I genuinely thought that hotplugging HDMI was just as safe as USB!

[Krathoon]

Surely, the HDMI port is not that touchy. I have plugged in the HDMI port on my working Mister numerous times while the monitor was running.

I still have not tried removing the IO board yet. I will do that when I get back.

[FPGA64]

Surely, the HDMI port is not that touchy. I have plugged in the HDMI port on my working Mister numerous times while the monitor was running.

I still have not tried removing the IO board yet. I will do that when I get back.

99 times it will be fine then on the 100th .....

Its always best not to swap a cable that can carry voltage while the device is plugged in

[antibolo]

Surely, the HDMI port is not that touchy. I have plugged in the HDMI port on my working Mister numerous times while the monitor was running.

I still have not tried removing the IO board yet. I will do that when I get back.

99 times it will be fine then on the 100th .....

Its always best not to swap a cable that can carry voltage while the device is plugged in

Always? No offense but this is a weird thing to say after USB has been mainstream for almost 30 years now?

[FPGA64]

We are not talking about USB we are talking about HDMI

[antibolo]

We are not talking about USB we are talking about HDMI

Yes that's my point, I don't understand why you suddenly started saying "a cable that can carry voltage" in the general sense.

[rcade]

Surely, the HDMI port is not that touchy. I have plugged in the HDMI port on my working Mister numerous times while the monitor was running.

You shouldn't! On the DE10 Nano there is no buffering or protection to HDMI port.