Can't get past square 1 !

[monaco87]

OK I bought a DE-10 about 18 months ago and am only now trying to get it set up for Mister. I thought I'd try the basic DE-10 with the supplied SD card with its Linux image to make sure everything was OK.... it doesn't seem to be. With the supplied Terasic card it starts, orange LED lights then nothing on the screen. After much tinkering I connected the serial console and I am getting the following:

Code: Select all

U-Boot SPL 2017.03-rc2 (Mar 30 2017 - 19:07:16)
/data/de10-nano/release-build-2017.03.31/build/tmp-angstrom-glibc/work/de10_nano-angstrom-linux-gnueabi/u-boot-socfpga/v2017.03+gitAUTOINC+d03450606b-r0/git/drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
/data/de10-nano/release-build-2017.03.31/build/tmp-angstrom-glibc/work/de10_nano-angstrom-linux-gnueabi/u-boot-socfpga/v2017.03+gitAUTOINC+d03450606b-r0/git/drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
/data/de10-nano/release-build-2017.03.31/build/tmp-angstrom-glibc/work/de10_nano-angstrom-linux-gnueabi/u-boot-socfpga/v2017.03+gitAUTOINC+d03450606b-r0/git/drivers/ddr/altera/sequencer.c: Calibration complete
Trying to boot from MMC1


U-Boot 2017.03-rc2 (Mar 30 2017 - 19:07:16 -0700)

CPU:   Altera SoCFPGA Platform
FPGA:  Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
BOOT:  SD/MMC Internal Transceiver (3.0V)
       Watchdog enabled
I2C:   ready
DRAM:  1 GiB                                                                                                                                                                                                                                           

MMC:   dwmmc0@ff704000: 0                                                                                                                                                                                                                              

*** Warning - bad CRC, using default environment                                                                                                                                                                                                       
                                                                                                                                                                                                                                                       

In:    serial                                                                                                                                                                                                                                          

Out:   serial                                                                                                                                                                                                                                          

Err:   serial                                                                                                                                                                                                                                          

Model: Terasic DE10-Nano                                                                                                                                                                                                                               

Net:                                                                                                                                                                                                                                                   

Error: ethernet@ff702000 address not set.                                                                                                                                                                                                              

No ethernet found.                                                                                                                                                                                                                                     

Hit any key to stop autoboot:  0                                                                                                                                                                                                                       

reading de10-nano.rbf                                                                                                                                                                                                                                  

3368700 bytes read in 231 ms (13.9 MiB/s)                                                                                                                                                                                                              

Setting bus to 2                                                                                                                                                                                                                                       

reading STARTUP.BMP                                                                                                                                                                                                                                    

** Unable to read file STARTUP.BMP **                                                                                                                                                                                                                  

reading de10_nano_hdmi_config.bin                                                                                                                                                                                                                      

72872 bytes read in 10 ms (6.9 MiB/s)                                                                                                                                                                                                                  
## Starting application at 0x0C100001 ...                                                                                                                                                                                                              
HDMI WARNING: No HDMI display detected                                                                                                                                                                                                                 

HDMI WARNING: no valid timing found, setting 1024x768 default                                                                                                                                                                                          

HDMI_vld_tmng_fnd = 0                                                                                                                                                                                                                                  

HDMI_h_active_pix = 1024                                                                                                                                                                                                                               

HDMI_h_blank_pix = 320                                                                                                                                                                                                                                 

HDMI_h_sync_off = 24                                                                                                                                                                                                                                   

HDMI_h_sync_width = 136                                                                                                                                                                                                                                

HDMI_v_active_lin = 768                                                                                                                                                                                                                                

HDMI_v_blank_lin = 38                                                                                                                                                                                                                                  

HDMI_v_sync_off = 3                                                                                                                                                                                                                                    

HDMI_v_sync_width = 6                                                                                                                                                                                                                                  

HDMI_pll_freq = 65000000                                                                                                                                                                                                                               

HDMI_pll_m = 9                                                                                                                                                                                                                                         

HDMI_pll_c = 7                                                                                                                                                                                                                                         

HDMI_pll_k = 429496724                                                                                                                                                                                                                                 

HDMI_stride = 4096                                                                                                                                                                                                                                     

HDMI_milestones = 1044607                                                                                                                                                                                                                              

HDMI INFO: bad BMP signature                                                                                                                                                                                                                           
## Application terminated, rc = 0x10                                                                                                                                                                                                                   
reading socfpga_cyclone5_de10_nano.dtb                                                                                                                                                                                                                 

29940 bytes read in 8 ms (3.6 MiB/s)                                                                                                                                                                                                                   

switch to partitions #0, OK                                                                                                                                                                                                                            

mmc0 is current device                                                                                                                                                                                                                                 

Unknown command 'part' - try 'help'                                                                                                                                                                                                                    

Scanning mmc 0:1...                                                                                                                                                                                                                                    

Found /extlinux/extlinux.conf                                                                                                                                                                                                                          

Retrieving file: /extlinux/extlinux.conf                                                                                                                                                                                                               

reading /extlinux/extlinux.conf                                                                                                                                                                                                                        

187 bytes read in 5 ms (36.1 KiB/s)                                                                                                                                                                                                                    

1:      Linux Default                                                                                                                                                                                                                                  

Retrieving file: /extlinux/../zImage                                                                                                                                                                                                                   

reading /extlinux/../zImage                                                                                                                                                                                                                            

8077048 bytes read in 544 ms (14.2 MiB/s)                                                                                                                                                                                                              

append: root=/dev/mmcblk0p2 rootwait mem=0x3F000000 memmap=16M$0x3F000000 ttyS0,115200                                                                                                                                                                 
## Flattened Device Tree blob at 00000100                                                                                                                                                                                                              
   Booting using the fdt blob at 0x000100                                                                                                                                                                                                              

   reserving fdt memory region: addr=0 size=1000                                                                                                                                                                                                       

   reserving fdt memory region: addr=100 size=7f00                                                                                                                                                                                                     

   Loading Device Tree to 03ff5000, end 03fffeff ... OK                                                                                                                                                                                                
                                                                                                                                                                                                                                                       

Starting kernel ...                                                                                                                                                                                                                                    

The board then repeatedly cycles endlessly through the following:

Code: Select all

                                                                                                                                                                                                                                            

U-Boot SPL 2017.03-rc2 (Mar 30 2017 - 19:07:16)                                                                                                                                                                                                        

/data/de10-nano/release-build-2017.03.31/build/tmp-angstrom-glibc/work/de10_nano-angstrom-linux-gnueabi/u-boot-socfpga/v2017.03+gitAUTOINC+d03450606b-r0/git/drivers/ddr/altera/sequencer.c: Preparing to start memory calibration                     

/data/de10-nano/release-build-2017.03.31/build/tmp-angstrom-glibc/work/de10_nano-angstrom-linux-gnueabi/u-boot-socfpga/v2017.03+gitAUTOINC+d03450606b-r0/git/drivers/ddr/altera/sequencer.c: CALIBRATION PASSED                                        

/data/de10-nano/release-build-2017.03.31/build/tmp-angstrom-glibc/work/de10_nano-angstrom-linux-gnueabi/u-boot-socfpga/v2017.03+gitAUTOINC+d03450606b-r0/git/drivers/ddr/altera/sequencer.c: Calibration complete                                      

Trying to boot from MMC1 

I have done nothing to the board except verify the switches, insert the supplied SD card and apply power, any ideas?

Thanks

[dickhardpill]

You need Mr Fusion?

https://github.com/MiSTer-devel/mr-fusion

edit to correct name.

[aberu]

Contact Terasic, don't install any MiSTer hardware onto it yet.

[Vic20-Ian]

https://github.com/MiSTer-devel/Wiki_Mi ... etup-Guide

I would install the MiSTer image on the SD card and try that.

I have a USB board underneath, memory board, a bluetooth dongle and wifi dongle fitted.

All 4 switches on my board are UP next to the black connector near them.

[FPGA64]

As Aberu said dont try and run Mister on it. Use the Terrasic supplied image. If that isnt working its the DE10 and you should contact terassic. As soon as you start trying to use Mister on it you will cause extra issues when you contact terassic for the return.

[Vic20-Ian]

As Aberu said dont try and run Mister on it. Use the Terrasic supplied image. If that isnt working its the DE10 and you should contact terassic. As soon as you start trying to use Mister on it you will cause extra issues when you contact terassic for the return.

Get a different SD card and put MiSTer on that and try it.

If that boots fine then it was the supplied SD card at fault which you don't need afterwards anyway.

If it doesn't boot MiSTer then return the DE10 with the original SD card.

[dickhardpill]

Running mr fusion on a completely separate SD card and attempting to boot will not hurt the DE10-nano and will not void any warranty.

[FPGA64]

As Aberu said dont try and run Mister on it. Use the Terrasic supplied image. If that isnt working its the DE10 and you should contact terassic. As soon as you start trying to use Mister on it you will cause extra issues when you contact terassic for the return.

Get a different SD card and put MiSTer on that and try it.

If that boots fine then it was the supplied SD card at fault which you don't need afterwards anyway.

If it doesn't boot MiSTer then return the DE10 with the original SD card.

Terrasic have had issues with Mister returns in the past so best if you do it to never mention Mister and just say you used the supplied image and it failed

[Vic20-Ian]

As Aberu said dont try and run Mister on it. Use the Terrasic supplied image. If that isnt working its the DE10 and you should contact terassic. As soon as you start trying to use Mister on it you will cause extra issues when you contact terassic for the return.

Get a different SD card and put MiSTer on that and try it.

If that boots fine then it was the supplied SD card at fault which you don't need afterwards anyway.

If it doesn't boot MiSTer then return the DE10 with the original SD card.

Terrasic have had issues with Mister returns in the past so best if you do it to never mention Mister and just say you used the supplied image and it failed

It is a consumer retail unit. The end user can check if is is working and use it for their purpose.

This includes using it with a new SD card configured with MiSTer software.

Turn the DE10 so the writing is correctly oriented.

Check the SW10 dip switches. Mine are 1,3,5,6 On (up) and 2,4 down (Off)

Check the four larger switches are down (Away from main chip and next to the 2 edge connector sockets)

If the unit boots with a new SD card formatted and setup for MiSTer then the supplied SD card was at fault and the user has a working MiSTer.

If the unit does not boot with a new SD card formatted and setup for MiSTer then the DE10 Nano is at fault and can be returned with the original SD card.

Running the MiSTer Software on the DE10 is not an issue to test the unit and return it if faulty.

Plugging in accessory boards incorrectly or using the wrong power supply and damaging it would be an issue.

[monaco87]

Thanks for all the replies. I contacted Terasic first, I've heard nothing since. MrFusion image produces the same results. Tried multiple uSD cards also created using different method (etcher, rufus Linux dd etc.) all produce the same result.

Nothing seems to be broken as I can interrogate the uSD card from the uBoot prompt using

Code: Select all

mmc part, mmc info

and other commands. I notice that the boot process says "Trying to boot from MMC1" whilst the uBoot commands identify the uSD card as MMC0. Not sure if that's relevant.

Is there any way to reinitialise the DE-10 card to stock (which it should have already!) using JTAG, or is the ARM boot hard coded?

Can't return to Terasic as the card is 18 months old, that's what I get for buying it and then leaving it for so long!

Thanks for all the replies

[Vic20-Ian]

Here is the boot image and start-up

de10-nano.terasic.com/cd

or here

https://www.terasic.com.tw/cgi-bin/page ... 6&PartNo=4

The source may also be there to recompile the image.

[monaco87]

Ok did a lot more digging regarding the boot process. The issue seems to be related to run hdmi_cfg issued by the boot process via run hdmi_init. This seems to loop until it gets sucessfull I2C comms via HDMI - however I'm seeing :

Code: Select all

HDMI ERROR: reading I2C

I think the Analog Devices ADV7513 may be kaput, maybe I did it plugging in the HDMI cable, maybe it was faulty from Terasic.

Will try and replace it and see.

[aberu]

Check your DIP switches

https://mister-devel.github.io/MkDocs_M ... -de10-nano

[monaco87]

Check your DIP switches

https://mister-devel.github.io/MkDocs_M ... -de10-nano

I checked the DIP switches are correct early on, even checked switch continuity with a meter.