MiSTer FPGA Forum

Im having a problem with my mister - VGA output works fine, but HDMI output has stopped working completely. Ive tried HDMI to DVI, HDMI to VGA and HDMI to HDMI - just get a blank screen with all of them.

Ive tried every option in the ini file

Ive tried scandoubler on/off, vga scaler on/off, hdmi limited 0-1-2, direct video 0,1, and tried variety of resolutions all without success.

My ini file below. Is there anything outwith the ini file that can stop the HDMI from functioning?

[MiSTer]
key_menu_as_rgui=0 ; set to 1 to make the MENU key map to RGUI in Minimig (e.g. for Right Amiga)
forced_scandoubler=0 ; set to 1 to run scandoubler on VGA output always (depends on core).
ypbpr=0 ; set to 1 for YPbPr on VGA output.
composite_sync=0 ; set to 1 for composite sync on HSync signal of VGA output.
vga_scaler=0 ; set to 1 to connect VGA to scaler output.
hdmi_audio_96k=0 ; set to 1 for 96khz/16bit HDMI audio (48khz/16bit otherwise)
keyrah_mode=0x18d80002 ; VIDPID of keyrah for special code translation (0x23418037 for Arduino Micro)
volumectl=0 ; enable audio volume control by multimedia keys
vscale_mode=0 ; 0 - scale to fit the screen height.
; 1 - use integer scale only.
; 2 - use 0.5 steps of scale.
; 3 - use 0.25 steps of scale.
vscale_border=0 ; set vertical border for TVs cutting the upper/bottom parts of screen (1-399)
;bootscreen=0 ; uncomment to disable boot screen of some cores like Minimig.
;mouse_throttle=10 ; 1-100 mouse speed divider. Useful for very sensitive mice
rbf_hide_datecode=0 ; 1 - hides datecodes from rbf file names. Press F2 for quick temporary toggle
menu_pal=0 ; 1 - PAL mode for menu core
hdmi_limited=0 ; 1 - use limited (16..235) color range over HDMI
; 2 - use limited (16..255) color range over HDMI, for VGA converters.
direct_video=0 ; 1 - enable core video timing over HDMI, use only with VGA converters.
fb_size=0 ; 0 - automatic, 1 - full size, 2 - 1/2 of resolution, 4 - 1/4 of resolution.
fb_terminal=0 ; 1 - enabled (default), 0 - disabled
osd_timeout=30 ; 5-3600 timeout (in seconds) for OSD to disappear in Menu core. 30 seconds if not set.
; Background picture will get darker after double timeout

; 1 - enables the recent file loaded/mounted.
; WARNING: This option will enable write to SD card on every load/mount which may wear the SD card after many writes to the same place
; There is also higher chance to corrupt the File System if MiSTer will be reset or powered off while writing.
recents=0

; lastcore - Autoboot the last loaded core (corename autosaved in CONFIG/lastcore.dat) first found on the SD/USB
; lastexactcore - Autoboot the last loaded exact core (corename_yyyymmdd.rbf autosaved in CONFIG/lastcore.dat) first found on the SD/USB
; corename - Autoboot first corename_*.rbf found on the SD/USB
; corename_yyyymmdd.rbf - Autoboot first corename_yyyymmdd.rbf found on the SD/USB
;bootcore=lastcore ; uncomment to autoboot a core, as the last loaded core.
bootcore_timeout=10 ; 10-30 timeout before autoboot, comment for autoboot without timeout.

; Option to load the custom font. Format is plain bitmap 8x8.
; Supported sizes of font:
; 768 bytes - chars 32-127 (only alpha + numeric)
; 1024 bytes - chars 0-127
; 1136 bytes - chars 0-141
; up to 2048 - only chars 0-141 will be used.
; if first 32 chars are empty (for sizes 1024 bytes and more) then they are skipped.
font=font/myfont.pf

; USER button emulation by keybaord. Usually it's reset button.
; 0 - lctrl+lalt+ralt (lctrl+lgui+rgui on keyrah)
; 1 - lctrl+lgui+rgui
; 2 - lctrl+lalt+del
; 3 - same as 0 (lctrl+lalt+ralt on keyrah)
reset_combo=0

dvi_mode=1 ; set to 1 for DVI mode. Audio won't be transmitted through HDMI in DVI mode.

; 0 - 1280x720@60
; 1 - 1024x768@60
; 2 - 720x480@60
; 3 - 720x576@50
; 4 - 1280x1024@60
; 5 - 800x600@60
; 6 - 640x480@60
; 7 - 1280x720@50
; 8 - 1920x1080@60
; 9 - 1920x1080@50
;10 - 1366x768@60
;11 - 1024x600@60
;
; custom mode: hact,hfp,hs,hbp,vact,vfp,vs,vbp,Fpix_in_KHz
; video_mode=1280,110,40,220,720,5,5,20,74250
video_mode=5

; set to 1-10 (seconds) to display video info on startup/change
video_info=0

; Set to 1 for automatic HDMI VSync rate adjust to match original VSync.
; Set to 2 for low latency mode (single buffer).
; This option makes video butter smooth like on original emulated system.
; Adjusting is done by changing pixel clock. Not every display supports variable pixel clock.
; For proper adjusting and to reduce possible out of range pixel clock, use 60Hz HDMI video
; modes as a base even for 50Hz systems.
vsync_adjust=1

; These parameters have the same format as video_mode.
; You need to supply both PAL and NTSC modes if you want vsync_adjust to switch between
; predefined modes as a base. This will reduce the range of pixel clock.
;video_mode_ntsc=5
;video_mode_pal=5

All looks fine to me. Have you tried with a fresh ini?

Depending on how you edited the ini, there could be stray hidden characters.

Yeah, ive reloaded all the ini's and tried all 4 of them with varying figures.

Im guessing the HDMI output is dead.

Have you tried to boot with the original SD card that comes with the DE10 Nano board ?

Remove all the add-ons first.

Yeah, troubleshooted everything, did a fresh install, the HDMI socket is dead. Replaced the Nano and its working again.

In my case HDMI works with Linux from the DE10 Nano's manual. This very strange.

You could try building a manual SD card instead of using Mr. Fusion. That might let you set up for ssh so you can connect to the board and see what's up.

You did try booting Mr. Fusion and the subsequent install without any boards attached, right? Just the naked DE-10?