MiSTer FPGA Forum

Code: Select all

[MiSTer]
key_menu_as_rgui=0     ; set to 1 to make the MENU key map to RGUI in Minimig (e.g. for Right Amiga)
forced_scandoubler=0   ; set to 1 to run scandoubler on VGA output always (depends on core).
ypbpr=0                ; set to 1 for YPbPr on VGA output.
composite_sync=0       ; set to 1 for composite sync on HSync signal of VGA output.
vga_scaler=0           ; set to 1 to connect VGA to scaler output.
hdmi_audio_96k=0       ; set to 1 for 96khz/16bit HDMI audio (48khz/16bit otherwise)
keyrah_mode=0x18d80002 ; VIDPID of keyrah for special code translation (0x23418037 for Arduino Micro)
vscale_mode=0          ; 0 - scale to fit the screen height.
                       ; 1 - use integer scale only.
                       ; 2 - use 0.5 steps of scale.
                       ; 3 - use 0.25 steps of scale.
vscale_border=0        ; set vertical border for TVs cutting the upper/bottom parts of screen (1-399)
;bootscreen=0          ; uncomment to disable boot screen of some cores like Minimig. 
;mouse_throttle=10     ; 1-100 mouse speed divider. Useful for very sensitive mice
rbf_hide_datecode=0    ; 1 - hides datecodes from rbf file names. Press F2 for quick temporary toggle
menu_pal=0             ; 1 - PAL mode for menu core
hdmi_limited=0         ; 1 - use limited (16..235) color range over HDMI
                       ; 2 - use limited (16..255) color range over HDMI, for VGA converters.
direct_video=0         ; 1 - enable core video timing over HDMI, use only with VGA converters.
fb_size=0              ; 0 - automatic, 1 - full size, 2 - 1/2 of resolution, 4 - 1/4 of resolution.
fb_terminal=1          ; 1 - enabled (default), 0 - disabled
osd_timeout=30         ; 5-3600 timeout (in seconds) for OSD to disappear in Menu core. 30 seconds if not set.
                       ; Background picture will get darker after double timeout
osd_rotate=0           ; Display OSD menu rotated,  0 - no rotation, 1 - rotate right (+90°), 2 - rotate left (-90°)                  

; 1 - enables the recent file loaded/mounted.
; WARNING: This option will enable write to SD card on every load/mount which may wear the SD card after many writes to the same place
;          There is also higher chance to corrupt the File System if MiSTer will be reset or powered off while writing.
recents=0

; lastcore - Autoboot the last loaded core (corename autosaved in CONFIG/lastcore.dat) first found on the SD/USB
; lastexactcore - Autoboot the last loaded exact core (corename_yyyymmdd.rbf autosaved in CONFIG/lastcore.dat) first found on the SD/USB
; corename - Autoboot first corename_*.rbf found on the SD/USB
; corename_yyyymmdd.rbf - Autoboot first corename_yyyymmdd.rbf found on the SD/USB
;bootcore=lastcore    ; uncomment to autoboot a core, as the last loaded core.
bootcore_timeout=10  ; 10-30 timeout before autoboot, comment for autoboot without timeout.

; Option to load the custom font. Format is plain bitmap 8x8.
; Supported sizes of font:
;   768 bytes - chars 32-127 (only alpha + numeric)
;  1024 bytes - chars 0-127
;  1136 bytes - chars 0-141
;  up to 2048 - only chars 0-141 will be used.
; if first 32 chars are empty (for sizes 1024 bytes and more) then they are skipped.
font=font/myfont.pf

; USER button emulation by keybaord. Usually it's reset button.
; 0 - lctrl+lalt+ralt (lctrl+lgui+rgui on keyrah)
; 1 - lctrl+lgui+rgui
; 2 - lctrl+lalt+del
; 3 - same as 0 (lctrl+lalt+ralt on keyrah)
reset_combo=0

dvi_mode=0             ; set to 1 for DVI mode. Audio won't be transmitted through HDMI in DVI mode.

; 0 - 1280x720@60
; 1 - 1024x768@60
; 2 - 720x480@60
; 3 - 720x576@50
; 4 - 1280x1024@60
; 5 - 800x600@60
; 6 - 640x480@60
; 7 - 1280x720@50
; 8 - 1920x1080@60
; 9 - 1920x1080@50
;10 - 1366x768@60
;11 - 1024x600@60
;12 - 1920x1440@60
;13 - 2048x1536@60
;
; custom mode: hact,hfp,hs,hbp,vact,vfp,vs,vbp,Fpix_in_KHz
;   video_mode=1280,110,40,220,720,5,5,20,74250
video_mode=0

; set to 1-10 (seconds) to display video info on startup/change
video_info=0

; Set to 1 for automatic HDMI VSync rate adjust to match original VSync.
; Set to 2 for low latency mode (single buffer).
; This option makes video butter smooth like on original emulated system.
; Adjusting is done by changing pixel clock. Not every display supports variable pixel clock.
; For proper adjusting and to reduce possible out of range pixel clock, use 60Hz HDMI video
; modes as a base even for 50Hz systems. 
vsync_adjust=0

; If you monitor doesn't support either very low (NTSC monitors may not support PAL) or 
; very high (PAL monitors may not support NTSC) then you can set refresh_min and/or refresh_max
; parameters, so vsync_adjust won't be applied for refreshes outside specified.
; These parameters are valid only when vsync_adjust is non-zero.
refresh_min=0
refresh_max=0

; These parameters have the same format as video_mode.
; You need to supply both PAL and NTSC modes if you want vsync_adjust to switch between
; predefined modes as a base. This will reduce the range of pixel clock.
;video_mode_ntsc=0
;video_mode_pal=7

; 1-10 (seconds) to display controller's button map upon first time key press
; 0 - disable
controller_info=6

; JammaSD/J-PAC/I-PAC keys to joysticks translation
; You have to provide correct VID and PID of your input device
; Examples: Legacy J-PAC with Mini-USB or USB capable I-PAC with PS/2 connectors VID=0xD209/PID=0x0301
; USB Capable J-PAC with only PS/2 connectors VID=0x04B4/PID=0x0101
; JammaSD: VID=0x04D8/PID=0xF3AD
jamma_vid=0x04D8
jamma_pid=0xF3AD

; Disable merging input devices. Use if only player 1 works.
; Leave no_merge_pid empty to apply this to all devices with the same VID.
;no_merge_vid=0x045E
;no_merge_pid=0x028E

; Speeds in sniper/non-sniper modes of mouse emulation by joystick 
; 0 - (default) - faster move in non-sniper mode, slower move in sniper mode.
; 1 - movement speeds are swapped.
sniper_mode=0

; Uncomment following option if you don't want to see a second line for long file names in listing.
;browse_expand=0

; 0 - disable MiSTer logo in Menu core
logo=1

; Custom shared folder for core supporting this feature (currently minimig and ao486 only)
; Can be relative to core's home dir or absolute path.
; Path must exist before core start to use it, or it will fail.
; Make sure USB device is mounted before use shared folder on USB!
shared_folder=

Code: Select all

LCD
Type: 19“ Wide TN colour TFT active matrix WSXGA+ LCD
Contrast Ratio: 1000:1 (typ.), 6000:1 DCR (typ.)
Viewing Angles: 170° horizontal, 160° vertical (at 10:1)

170° horizontal, 170° vertical (at 5:1)
Brightness: 300 cd/m2
Display Area: 41.0cm horizontal x 25.7cm vertical, 48.3cm diagonal
Optimum Resolution: 1680 x 1050 @60Hz
Response Time: Up to 2ms (grey-to-grey), 5ms (off-on-off) (typ.)
Light Source: Long life, 40000 hrs. (min.)
Panel Surface: Anti-glare (3H)
Pixel Pitch: 0.243mm
Colour Support: 16.7M colours supported (6-bit+2-bit FRC)
Pixel Clock: 165MHz
COMPATIBILITY
PC: VGA up to 1680x1050 non-interlaced
Mac®: Power Mac™ up to 1680 x 1050 non-interlaced
DIMENSIONS
Physical With Stand: 447 x 399 x 175
Physical Without Stand: 447 x 317 x 52
W x H x D mm: 510 x 465 x 135
PACKAGE CONTENTS
LCD Monitor, power cable, 15-pin VGA video cable, DVI cable, Quick Start Guide, ViewSonic Wizard CD-ROM (multi-language User Guides/drivers and SRS WOW HD software)
WARRANTY
Three-year limited warranty on parts, labor and backlight.
AUDIO
Speaker: 2 x 3 watt integrated invisible stereo speakers w. SRS WOW HD
CONNECTOR
Analogue: 15-pin mini D-Sub (detachable cable)
Digital: 24-pin DVI-D (detachable cable) (HDCP enabled)
Power: 3-pin AC plug (CEE22)
Audio: 3.5mm stereo audio line-in
POWER
Voltage: AC 100–240 V, 50–60 Hz (auto switch), internal power supply
Consumption: 44 watt (typ.), <=1 watt in power save mode
CONTROLS
Basic: Power, menu [1], select [2], up, down
OnView®: Auto image adjust, contrast, brightness, input select (D-sub, DVI-D), Audio adjust (volume, mute), ViewMatch® colour adjust (sRGB, 9300K, 7500K, 6500K, 5000K, user RGB), information (resolution, H/V frequency, pixel clock, model number, serial number), manual image adjust (H/V position, H size, fine tune, sharpness, DCR [on/off], aspect ratio [1:1, 4:3, 16:9, fill aspect ratio, fill full screen], response time [standard, advanced, ultrafast]), setup menu (language [11 options], resolution notice, OSD position, OSD timeout, OSD background), OSD/power lock,
memory recall.
OSD: Auto image adjust, contrast, brightness, input select (D-sub, DVI-D), Audio adjust (volume, mute), ViewMatch® colour adjust (sRGB, 9300K, 7500K, 6500K, 5000K, user RGB), information (resolution, H/V frequency, pixel clock, model number, serial number), manual image adjust (H/V position, H size, fine tune, sharpness, DCR [on/off], aspect ratio [1:1, 4:3, 16:9, fill aspect ratio, fill full screen], response time [standard, advanced, ultrafast]), setup menu (language [11 options], resolution notice, OSD position, OSD timeout, OSD background), OSD/power lock,
memory recall.
OPERATING CONDITIONS
Temperature: 0°C – 35°C
Humidity: 10%–90% (non-condensation)
WEIGHT
Net With Stand: 3.9kg
Net Without Stand: 3.1kg
Packaging: 5.2kg
VIDEO INPUT
Analog/Digital: RGB analogue (0.7/1.0 Vp-p, 75 ohm, DDC/CI)
Frequency: Fh: 24-82kHz, Fv: 50-75Hz
Sync: H/V separated (TTL), composite, sync-on-green
Digital: DVI-D (HDCP enabled, TMDS, 100 ohm, DDC/CI)
POWER MANAGEMENT
Meets ENERGY and ENERGY STAR standards
SECURITY
Kensington® security port[code]

Code: Select all

[MiSTer]
;VIDEO MODE
video_mode=1680,104,176,280,1050,3,6,30,146250
;VIDEO SETTINGS
menu_pal = 0
dvi_mode = 0
fb_terminal = 1
fb_size = 0
video_info = 0
hdmi_limited = 0
vsync_adjust = 0
;VGA SETTINGS
forced_scandoubler = 0
ypbpr = 0
composite_sync = 0
vga_scaler = 1
direct_video = 0
;VIDEO SCALING
vscale_mode = 0
vscale_border = 0
;AUDIO SETTINGS
hdmi_audio_96k = 0
volumectl = 1
;MISC SETTINGS
key_menu_as_rgui = 0
rbf_hide_datecode = 0
;bootscreen = 0
recents = 1
gamepad_defaults = 1
keyrah_mode = 0x18d80002
reset_combo = 0
osd_timeout = 30
bootcore_timeout = 10

Code: Select all

[MiSTer]
key_menu_as_rgui=0     ; set to 1 to make the MENU key map to RGUI in Minimig (e.g. for Right Amiga)
forced_scandoubler=0   ; set to 1 to run scandoubler on VGA output always (depends on core).
ypbpr=0                ; set to 1 for YPbPr on VGA output.
composite_sync=0       ; set to 1 for composite sync on HSync signal of VGA output.
vga_scaler=1           ; set to 1 to connect VGA to scaler output.
hdmi_audio_96k=0       ; set to 1 for 96khz/16bit HDMI audio (48khz/16bit otherwise)
keyrah_mode=0x18d80002 ; VIDPID of keyrah for special code translation (0x23418037 for Arduino Micro)
vscale_mode=0          ; 0 - scale to fit the screen height.
                       ; 1 - use integer scale only.
                       ; 2 - use 0.5 steps of scale.
                       ; 3 - use 0.25 steps of scale.
vscale_border=0        ; set vertical border for TVs cutting the upper/bottom parts of screen (1-399)
;bootscreen=0          ; uncomment to disable boot screen of some cores like Minimig. 
;mouse_throttle=10     ; 1-100 mouse speed divider. Useful for very sensitive mice
rbf_hide_datecode=0    ; 1 - hides datecodes from rbf file names. Press F2 for quick temporary toggle
menu_pal=0             ; 1 - PAL mode for menu core
hdmi_limited=0         ; 1 - use limited (16..235) color range over HDMI
                       ; 2 - use limited (16..255) color range over HDMI, for VGA converters.
direct_video=0         ; 1 - enable core video timing over HDMI, use only with VGA converters.
fb_size=0              ; 0 - automatic, 1 - full size, 2 - 1/2 of resolution, 4 - 1/4 of resolution.
fb_terminal=1          ; 1 - enabled (default), 0 - disabled
osd_timeout=30         ; 5-3600 timeout (in seconds) for OSD to disappear in Menu core. 30 seconds if not set.
                       ; Background picture will get darker after double timeout
osd_rotate=0           ; Display OSD menu rotated,  0 - no rotation, 1 - rotate right (+90°), 2 - rotate left (-90°)                  

; 1 - enables the recent file loaded/mounted.
; WARNING: This option will enable write to SD card on every load/mount which may wear the SD card after many writes to the same place
;          There is also higher chance to corrupt the File System if MiSTer will be reset or powered off while writing.
recents=0

; lastcore - Autoboot the last loaded core (corename autosaved in CONFIG/lastcore.dat) first found on the SD/USB
; lastexactcore - Autoboot the last loaded exact core (corename_yyyymmdd.rbf autosaved in CONFIG/lastcore.dat) first found on the SD/USB
; corename - Autoboot first corename_*.rbf found on the SD/USB
; corename_yyyymmdd.rbf - Autoboot first corename_yyyymmdd.rbf found on the SD/USB
;bootcore=lastcore    ; uncomment to autoboot a core, as the last loaded core.
bootcore_timeout=10  ; 10-30 timeout before autoboot, comment for autoboot without timeout.

; Option to load the custom font. Format is plain bitmap 8x8.
; Supported sizes of font:
;   768 bytes - chars 32-127 (only alpha + numeric)
;  1024 bytes - chars 0-127
;  1136 bytes - chars 0-141
;  up to 2048 - only chars 0-141 will be used.
; if first 32 chars are empty (for sizes 1024 bytes and more) then they are skipped.
font=font/myfont.pf

; USER button emulation by keybaord. Usually it's reset button.
; 0 - lctrl+lalt+ralt (lctrl+lgui+rgui on keyrah)
; 1 - lctrl+lgui+rgui
; 2 - lctrl+lalt+del
; 3 - same as 0 (lctrl+lalt+ralt on keyrah)
reset_combo=0

dvi_mode=0             ; set to 1 for DVI mode. Audio won't be transmitted through HDMI in DVI mode.

; 0 - 1280x720@60
; 1 - 1024x768@60
; 2 - 720x480@60
; 3 - 720x576@50
; 4 - 1280x1024@60
; 5 - 800x600@60
; 6 - 640x480@60
; 7 - 1280x720@50
; 8 - 1920x1080@60
; 9 - 1920x1080@50
;10 - 1366x768@60
;11 - 1024x600@60
;12 - 1920x1440@60
;13 - 2048x1536@60
;
; custom mode: hact,hfp,hs,hbp,vact,vfp,vs,vbp,Fpix_in_KHz
;   video_mode=1280,110,40,220,720,5,5,20,74250
video_mode=1680,104,176,280,1050,3,6,30,146250

; set to 1-10 (seconds) to display video info on startup/change
video_info=0

; Set to 1 for automatic HDMI VSync rate adjust to match original VSync.
; Set to 2 for low latency mode (single buffer).
; This option makes video butter smooth like on original emulated system.
; Adjusting is done by changing pixel clock. Not every display supports variable pixel clock.
; For proper adjusting and to reduce possible out of range pixel clock, use 60Hz HDMI video
; modes as a base even for 50Hz systems. 
vsync_adjust=0

; If you monitor doesn't support either very low (NTSC monitors may not support PAL) or 
; very high (PAL monitors may not support NTSC) then you can set refresh_min and/or refresh_max
; parameters, so vsync_adjust won't be applied for refreshes outside specified.
; These parameters are valid only when vsync_adjust is non-zero.
refresh_min=0
refresh_max=0

; These parameters have the same format as video_mode.
; You need to supply both PAL and NTSC modes if you want vsync_adjust to switch between
; predefined modes as a base. This will reduce the range of pixel clock.
;video_mode_ntsc=0
;video_mode_pal=7

; 1-10 (seconds) to display controller's button map upon first time key press
; 0 - disable
controller_info=6

; JammaSD/J-PAC/I-PAC keys to joysticks translation
; You have to provide correct VID and PID of your input device
; Examples: Legacy J-PAC with Mini-USB or USB capable I-PAC with PS/2 connectors VID=0xD209/PID=0x0301
; USB Capable J-PAC with only PS/2 connectors VID=0x04B4/PID=0x0101
; JammaSD: VID=0x04D8/PID=0xF3AD
jamma_vid=0x04D8
jamma_pid=0xF3AD

; Disable merging input devices. Use if only player 1 works.
; Leave no_merge_pid empty to apply this to all devices with the same VID.
;no_merge_vid=0x045E
;no_merge_pid=0x028E

; Speeds in sniper/non-sniper modes of mouse emulation by joystick 
; 0 - (default) - faster move in non-sniper mode, slower move in sniper mode.
; 1 - movement speeds are swapped.
sniper_mode=0

; Uncomment following option if you don't want to see a second line for long file names in listing.
;browse_expand=0

; 0 - disable MiSTer logo in Menu core
logo=1

; Custom shared folder for core supporting this feature (currently minimig and ao486 only)
; Can be relative to core's home dir or absolute path.
; Path must exist before core start to use it, or it will fail.
; Make sure USB device is mounted before use shared folder on USB!
shared_folder=